Husqvarna DMS 240 Complete Rig Specs

VERIFIED SPECIFICATION · ACTIVE · Last verified 2026-08-22

10" stand-mounted rig concrete core drill

Maximum diameter: 10"
Power: 3.3 hp
Voltage: 120V
Speeds: 390 / 890 RPM
Spindle: 1-1/4"-7 UNC Male (Outer) / G 1/2" Female (Inner)
Handheld: No
Stand capable: Yes
Wet drilling: Yes
Dry drilling: Yes
Safety clutch: Unknown / Not specified by manufacturer
Machine weight: 13 lb

Values are taken from manufacturer documentation and official manuals where cited in Sources. Position 1: 390 rpm idle; Position 2: 890 rpm idle (OEM OM)

Find Compatible Bits Build Complete System Best Core Drills

Not sold on Amazon. Available through authorized Husqvarna dealers.

Decision Summary

Specification analysis for Husqvarna DMS 240 based on verified manufacturer manuals and operator documentation.

✓ Best Suited For

General professional complete stand system up to 10".

✕ Who Should Skip

You need a non-proprietary chuck machine or bare-tool budget setup.

Key Operational Realities

One complete-rig machine row, not separate motor + stand products.

Verified specification table

Specification	Value	Source status
Maximum diameter	10"	Manufacturer verified
Voltage	120V	Manufacturer verified
Power	3.3 hp	Manufacturer verified
Low gear / min RPM	390	Manual verified
High gear / max RPM	890	Manual verified
Spindle	1-1/4"-7 UNC Male (Outer) / G 1/2" Female (Inner)	Manual verified
Handheld	No	Manual verified
Stand capable	Yes	Manual verified
Safety clutch	Unknown / Not specified by manufacturer	not listed
Water feed	Yes	Manual verified
Wet drilling	Yes	Manufacturer verified
Dry drilling	Yes	Manufacturer verified
Reinforced concrete	Yes	Manufacturer verified
Machine / net weight	13 lb	Manufacturer verified

Source links appear in Sources & Verification below, not invented ratings.

Bit & Rig Compatibility

Spindle interface, bit connection standards, and rig pairing documentation.

Spindle Connection: 1-1/4"-7 UNC Male (Outer) / G 1/2" Female (Inner)

This machine utilizes a 1-1/4"-7 UNC Male (Outer) / G 1/2" Female (Inner) spindle. Diamond core bits matching this connection thread directly without adapters. Mismatched threads require a documented rigid arbor adapter.

Compatible core bits

Mechanical fit is not the same as a safe operating-speed fit. Bit published max RPM wins when lower than the machine gear.

VERIFIED FIT ✅

Husqvarna DRI-5-2 2″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC ✓
Diameter 2" ✓
Machine capacity 10"
Method Dry
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

Husqvarna DRI-8-2 2″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC ✓
Diameter 2" ✓
Machine capacity 10"
Method Dry
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

SPEC-MATCHED 🟡

Hilti SPX-T Dry Tile & Anchor Core Bits 1/4″

SPEC-MATCHED 🟡

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.25" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 5/16″

SPEC-MATCHED 🟡

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.3125" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 3/8″

SPEC-MATCHED 🟡

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.375" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-L Heavy Rebar Wet Core Bits 1/2″

SPEC-MATCHED 🟡

Connection Hilti BL Quick-Release / 1-1/4"-7 UNC ✓
Diameter 0.5" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 1/2″

SPEC-MATCHED 🟡

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.5" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Milwaukee 48-17-5006 0.625″ Diamond Core Bit

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC Female ✓
Diameter 0.625" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Within published range
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 3/4″

SPEC-MATCHED 🟡

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.75" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Milwaukee 48-17-5007 0.75″ Diamond Core Bit

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC Female ✓
Diameter 0.75" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Within published range
OEM fit Not OEM-documented

View Bit Details Check RPM

Find more compatible bits

RPM / gear guidance

Position 1: 390 rpm idle; Position 2: 890 rpm idle (OEM OM)

Documented RPM: 390 / 890

Open RPM Calculator

Stand / adapter compatibility

Stand model: DMS 240 complete system
Stand compatibility: Complete rig
Adapter requirements: Unknown / Not specified by manufacturer
Adapter support: ["outer 1-1/4"-7 UNC","inner 5/8"-11 UNC"]

Water / slurry / dust

No evidence-backed water or dust accessory edges stored for this motor yet, do not invent recommendations.

Jobsite Setup & Operation

Operational workflow, slurry/water management, mounting procedures, and operator safety.

Water / slurry / dust

No evidence-backed water or dust accessory edges stored for this motor yet, do not invent recommendations.

Ownership & Service

Lifecycle status: CURRENT
Warranty evidence: UNKNOWN, UNKNOWN exact years, see Husqvarna Construction US Limited Warranty
OEM service: OEM service available, OEM service via Husqvarna Construction authorized servicing dealer/center network (Manufacturer Documentation). Complete-rig SKU.
Replacement parts status: Data incomplete
Not verified: specific replacement SKUs not confirmed in current OEM documentation for this model.
Last serviceability verification: 2026-08-21

Authoritative Sources & Verification

CoringSpec specifications are extracted directly from primary manufacturer documentation and operator manuals. We do not invent lab scores or extrapolate unverified ratings.

Verified Documentation

Research & Verification Standards: This equipment profile was audited and verified against primary manufacturer technical documentation by the CoringSpec Technical Editorial Team. Specifications confirmed active as of 2026-08-22.

Read Our Research Methodology · Report a Specification Correction