BLUEROCK 10Z1 Specs, Capacity & Compatibility

VERIFIED SPECIFICATION · ACTIVE · Last verified 2026-08-22

10" stand-mounted rig concrete core drill

Maximum diameter: 10"
Power: 2600W
Voltage: 110V, 50, 60 Hz, single phase
Speeds: 460 / 900 RPM
Spindle: 1-1/4"-7 UNC
Handheld: No
Stand capable: Yes
Wet drilling: Yes
Dry drilling: Yes
Safety clutch: Yes
Machine weight: Not clearly specified by manufacturer

Values are taken from manufacturer documentation and official manuals where cited in Sources. Gear 2: 900 rpm for 1", 4" bits; Gear 1: 460 rpm for 4", 10" bits (manufacturer manual)

Find Compatible Bits Build Complete System Best Core Drills

Check Amazon AvailabilityPaid link

Decision Summary

Specification analysis for BLUEROCK 10Z1 based on verified manufacturer manuals and operator documentation.

✓ Best Suited For

Large-diameter value stand rig up to 10" for commercial concrete and utility penetrations.

✕ Who Should Skip

You need portability, cordless power, or diameters under 4" where a smaller Z1 unit suffices.

Key Operational Realities

Requires 30A circuit per manual, do not assume a 20A garage outlet is sufficient.

Verified specification table

Specification	Value	Source status
Maximum diameter	10"	Manufacturer verified
Voltage	110V, 50, 60 Hz, single phase	Manufacturer verified
Power	2600W	Manufacturer verified
Low gear / min RPM	460	Manual verified
High gear / max RPM	900	Manual verified
Spindle	1-1/4"-7 UNC	Manual verified
Handheld	No	Manual verified
Stand capable	Yes	Manual verified
Safety clutch	Yes	Manual verified
Water feed	Yes	Manual verified
Wet drilling	Yes	Manufacturer verified
Dry drilling	Yes	Manufacturer verified
Reinforced concrete	Yes	Manufacturer verified
Machine / net weight	Not clearly specified by manufacturer	Definition conflict, not published as machine weight
Shipping weight	76 lb	Manual / listing (shipping)
Weight definition	Manual shipping weight 76 lb; net machine weight not clearly specified.

Source links appear in Sources & Verification below, not invented ratings.

Bit & Rig Compatibility

Spindle interface, bit connection standards, and rig pairing documentation.

Spindle Connection: 1-1/4"-7 UNC

This machine utilizes a 1-1/4"-7 UNC spindle. Diamond core bits matching this connection thread directly without adapters. Mismatched threads require a documented rigid arbor adapter.

Compatible core bits

Mechanical fit is not the same as a safe operating-speed fit. Bit published max RPM wins when lower than the machine gear.

VERIFIED FIT ✅

BLUEROCK Wet 1″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 1" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 2″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 2" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 3″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 3" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 4″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 4" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 5″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 5" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 6″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 6" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 8″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 8" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

BLUEROCK Wet 10″ Diamond Core Bit

VERIFIED FIT ✅

Connection 1-1/4"-7 UNC Female ✓
Diameter 10" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

SPEC-MATCHED 🟡

Hilti SPX-L Heavy Rebar Wet Core Bits 1/2″

SPEC-MATCHED 🟡

Connection Hilti BL Quick-Release / 1-1/4"-7 UNC ✓
Diameter 0.5" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-L Heavy Rebar Wet Core Bits 1″

SPEC-MATCHED 🟡

Connection Hilti BL Quick-Release / 1-1/4"-7 UNC ✓
Diameter 1" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Husqvarna VARI-DRILL Dry D20 Core Bits 1-1/4″

SPEC-MATCHED 🟡

Connection 5/8"-11 UNC & 1-1/4"-7 UNC ✓
Diameter 1.25" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Milwaukee 48-17-0112 1.25″ Diamond Core Bit

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC ✓
Diameter 1.25" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Within published range
OEM fit Not OEM-documented

View Bit Details Check RPM

Diamond Products Core Bore Premium Black Wet Core Bits 1-1/2″

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC Female ✓
Diameter 1.5" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Husqvarna Elite-Drill D1410 High-Speed Wet Core Bits 1-1/2″

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC Female ✓
Diameter 1.5" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Shibuya Shibuya Blue Bit Heavy Rebar Wet Core Bits 1-1/2″

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC & A-Rod ✓
Diameter 1.5" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

BLUEROCK BLUEROCK Supreme High Speed Wet Core Bits 2″

SPEC-MATCHED 🟡

Connection 1-1/4"-7 UNC Female ✓
Diameter 2" ✓
Machine capacity 10"
Method Wet
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

ADAPTER REQUIRED 🟠

Hilti SPX-T Dry Tile & Anchor Core Bits 1/4″

ADAPTER REQUIRED 🟠

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.25" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 5/16″

ADAPTER REQUIRED 🟠

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.3125" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 3/8″

ADAPTER REQUIRED 🟠

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.375" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 1/2″

ADAPTER REQUIRED 🟠

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.5" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Milwaukee 48-17-5006 0.625″ Diamond Core Bit

ADAPTER REQUIRED 🟠

Connection 1-1/4"-7 UNC Female ✓
Diameter 0.625" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

Hilti SPX-T Dry Tile & Anchor Core Bits 3/4″

ADAPTER REQUIRED 🟠

Connection 5/8"-11 UNC / M14 ✓
Diameter 0.75" ✓
Machine capacity 10"
Method Dry
OEM pairing Not OEM-documented
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Not OEM-documented

View Bit Details Check RPM

Milwaukee 48-17-5007 0.75″ Diamond Core Bit

ADAPTER REQUIRED 🟠

Connection 1-1/4"-7 UNC Female ✓
Diameter 0.75" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

Milwaukee 48-17-5009 0.875″ Diamond Core Bit

ADAPTER REQUIRED 🟠

Connection 1-1/4"-7 UNC Female ✓
Diameter 0.875" ✓
Machine capacity 10"
Method Wet
OEM pairing Verified ✓
Mechanical fit Aligned
Operating speed Unknown / incomplete RPM data
OEM fit Verified ✓

View Bit Details Check RPM

Find more compatible bits

RPM / gear guidance

Gear 2: 900 rpm for 1", 4" bits; Gear 1: 460 rpm for 4", 10" bits (manufacturer manual)

Documented RPM: 460 / 900

Open RPM Calculator

Stand / adapter compatibility

Stand model: Integrated stand, 31.5" height, 21" travel
Stand compatibility: Base must be wedge-anchored; 10Z1/RB variant adds rolling base per separate manual
Adapter requirements: Verify spindle / thread on the exact 10Z1 variant before ordering bits
Adapter support: ["1-1/4" u2192 5/8"-11 UNC adapter"]

Water / slurry / dust

No evidence-backed water or dust accessory edges stored for this motor yet, do not invent recommendations.

Jobsite Setup & Operation

Operational workflow, slurry/water management, mounting procedures, and operator safety.

Water / slurry / dust

No evidence-backed water or dust accessory edges stored for this motor yet, do not invent recommendations.

Ownership & Service

Lifecycle status: CURRENT
Warranty evidence: Warranty documented, 30-day limited warranty per BLUEROCK business policy, confirm current page; optional 12-month extended parts warranty sold separately
OEM service: OEM service available, OEM service/support via BLUEROCK Tools customer support (manufacturer channel). Spindle thread remains UNKNOWN until exact 10Z1 variant is locked.
Replacement parts status: OEM part available
Not verified: specific replacement SKUs not confirmed in current OEM documentation for this model.
Last serviceability verification: 2026-08-21

Authoritative Sources & Verification

CoringSpec specifications are extracted directly from primary manufacturer documentation and operator manuals. We do not invent lab scores or extrapolate unverified ratings.

Verified Documentation

Research & Verification Standards: This equipment profile was audited and verified against primary manufacturer technical documentation by the CoringSpec Technical Editorial Team. Specifications confirmed active as of 2026-08-22.

Read Our Research Methodology · Report a Specification Correction